Two hundred years ago, a British-born printer and author named Henry James was commissioned by the king to create the first poster advertising the new year.

He was working on a set of 12 printed lithographs for an ad campaign for the first edition of his novel, Jameson. 

Henry Jameson was published in 1849, in the first printing of the New Yorker, and was soon followed by the famous adverts of the decade.

Henry James is now a museum exhibit and one of the most well-known posters of the 19th century. 

In his autobiography, James wrote about how the first editions of Jameson had been printed and put up by the printer Jameson himself. 

Jameson’s 1849 poster adverts were printed on a single sheet of paper, and were sold on a large sheet of lithograph paper. 

The sheet of printed lithograph sheets was made by a small printer, and printed on sheets of paper of the same size. 

At first, the sheets were not exactly the same.

The paper was thick, and sometimes the edges of the printed sheets were so uneven that the lithographs could not be reproduced exactly. 

It took several years for the lithograph sheet to be printed on the first print run of Jamesons first printing. 

This was a good thing, because Jameson’s first printing, which was published on October 1, 1849 was not a hit, and Jameson and his publisher were unhappy with the print quality.

After the first prints were finished, the lithographers were allowed to take the sheet of sheet paper and print it on a different sheet of metal, so the printed sheet of Jamesones lithographs became the next Jameson sheet. 

As the lithographer printed on different sheets, they were able to get a better result.

The first printings were sold in a large number of sheets, so that Jamesons first lithographs did not sell out. 

By the time the first lithograph plates were printed, they had a good reputation, and the lithography industry was booming. 

For the next fifty years, the printing industry was flourishing. 

But in the mid-1950s, with the introduction of the mass-market printing press, the industry was going through a crisis.

The printing press was not good at producing a high-quality lithograph copy of a Jameson, and so many Jamesons that were being printed were not being printed at all.

With the printing presses struggling to produce quality Jamesons, the production of Jamesonee, a copy of James one, was also suffering. 

What caused this crisis?

The printing press had been around for a very long time, but in the 1970s, when the production boom began, the process of printing Jamesones first lithography began to be disrupted. 

One of the first things that happened was that a new method of making Jamesones was developed. 

To print on a sheet of steel, the plates were then heated to the melting point.

The molten metal is poured onto a hot, flat sheet of aluminum and the sheet is heated until the metal is just hot enough to melt the sheet.

The process of melting is repeated until the entire sheet is ready to be assembled. 

If the lithographic plate is not made with the same quality as Jamesones original printing, it will not be produced. 

Some people call this process the “melt-through” process. 

A new method was developed in which a sheet was heated to a temperature where the molten metal would melt at an angle.

This method was much faster than the original process, which involved melting the sheet at the same rate every time.

The plate was then put through a series of tests to see if it could be printed at high-temperature.

Many Jamesones were printed at a much lower temperature, and some printed at much higher temperatures, than the Jamesones printed on Jamesones previous printing.

However, the new process was still slower than the previous process.

During the melt-through process, a different type of metal was used to print the lithographical plates.

The metal that would melt was also used to melt a thin layer of steel.

The thin steel layer was then laid onto a plate of a different metal.

The steel layer melted and the steel sheet was removed. 

During the first step of the melt process, the thin metal layer was exposed to the air, and a heat gun was then heated through the metal to make it melt. 

After the metal had melted, the heat gun had to be removed, and then the heat source was changed.

This changed the process again. 

 Now, the melt and the heat were done simultaneously, and after the melt was complete, the metal was allowed to cool down and the process repeated.

These two processes were used to make Jamesones new lithograph, which became known as the Jamesone